On this page down the page you can discover a lot of quality details with regards to A Step-by-Step Guide to Installing a Bathtub.
Setting up a tub isn't exactly rocket science, however it does need strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bath tub with a brand-new one is additionally a reasonably hard job. If the old bathtub is readily accessible, the project can move immediately; if you need to open up a wall to remove the old bathtub and position the brand-new bathtub, the task is a lot harder. In either case, the task is within a house handyman's skills, although you will require a helper to leave the old bathtub and set in the brand-new one. Ensure you have actually certified on your own for the work and are comfortable attempting it. Rather than hiring a service provider to take control of a halfway-completed project, it is far better to take into consideration employing one before you start. Possibilities are you might need a professional plumber to make tube links.
This post will aid you install a brand-new bathtub in your restroom if you have actually currently bought a brand-new tub as well as do not require to change the plan of your previous water pipelines.
Your tools and product checklist ought to comprise the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your setup, then the first thing you must do is separate the water. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather bothersome as a result of the limited gain access to that is commonly the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a towel prepared for the remaining water that will come from the pipes. As soon as the supply pipelines have actually been removed, use the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from transforming during this process. When the taps have actually been removed, the holes in the bath/basin will need to be cleaned up of any kind of old sealing substance.
Before moving on to fit the brand-new faucets, compare the pipeline links on the old faucets to the new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic adapter to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly require minimizing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making certain that the washers are in location between the tap as well as the sink. Secure the tap in place with the producer offered backnut. As soon as the faucet is firmly in position, the supply pipes can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular faucet ports. The former type ought to be connected to the faucet finishes first, tightening only by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Setting up the Bathtub
Making use of both wooden boards under its feet, position the bath tub in the called for setting. The wooden boards are useful in evenly spreading the weight of the bathtub over the area of the boards rather than focusing all the weight onto 4 little points.
The following objective is to make certain that the bath tub is leveled all round. This can be achieved by examining the spirit level and readjusting the feet on the bathtub till the spirit level checks out degree.
To set up faucets, fit the bottom of the outermost flexible tap port to the appropriate supply pipe by making a compression sign up with; then do the same for the various other faucet.
Activate the water supply and also inspect all joints as well as brand-new pipework for leaks and also tighten them if needed. Fill up the bath tub and also examine the overflow outlet and the regular outlet for leakages.
Finally, repair the bathroom paneling as described in the supplier's user's manual. Tiling as well as sealing around the bathtub ought to wait till the bath tub has actually been made use of a minimum of once as this will resolve it right into its final setting.
Getting ready for the Installation
Firstly, the sustaining frame provided with the bath should be fitted (if called for) according to the producer's instructions. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is necessary to make certain that if the faucet comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps system to stop strain on the tub.
Fit the adaptable tap adapters to the bottom of the two taps making use of 2 nuts and olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. Make sure you utilize all of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom need to currently be ready to be fitted in its last position.
Tiling Around the Tub
In the area where the bathroom fulfills the ceramic tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the installation can move enough to break a stiff seal, triggering the water to permeate the wall surface between the bath and the tiling, causing issues with wetness as well as possible leaks to the ceiling below.
You can select from a variety of coloured sealers to assimilate your fixtures as well as fittings. They are marketed in tubes as well as cartridges, and also can sealing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with spins of soaked newspaper or soft rope. Remember to always load the bathtub with water prior to securing, to allow for the motion experienced when the bathtub is in use. The sealer can fracture fairly early if you do not take into account this movement prior to securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally conveniently offered on the market. It is suggested to fit the floor tiles utilizing waterproof or water resistant adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
Hopefully you enjoyed our section on Tools You Need to Install a New Bathtub . Thanks a ton for taking a few minutes to read through our short article. Sharing is nice. You never know, you may very well be helping someone out. Many thanks for your time spent reading it.
Don't delay; get expert help.